MPLS Working Group J. Rajamanickam, Ed. Internet-Draft R. Gandhi, Ed. Intended status: Experimental Cisco Systems, Inc. Expires: 8 June 2025 R. Zigler Broadcom H. Song Futurewei Technologies K. Kompella Juniper Networks 5 December 2024 MPLS Network Action (MNA) Sub-Stack Solution draft-ietf-mpls-mna-hdr-10 Abstract This document defines the MPLS Network Actions (MNA) sub-stack solution for carrying Network Actions and Ancillary Data in the label stack. MPLS Network Actions can be used to influence packet forwarding decisions, carry additional Operations, Administration, and Maintenance information in the MPLS packet or perform user- defined operations. This solution document specifies In-stack network action and In-stack data specific requirements found in "Requirements for MPLS Network Actions". This document follows the architectural framework for the MNA technologies specified in "MPLS Network Actions (MNA) Framework". This document describes an experiment whose purpose is to demonstrate that the MNA can be implemented and deployed. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 8 June 2025. Rajamanickam, et al. Expires 8 June 2025 [Page 1] Internet-Draft MNA Sub-Stack Solution December 2024 Copyright Notice Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Conventions Used in This Document . . . . . . . . . . . . . . 3 2.1. Requirements Language . . . . . . . . . . . . . . . . . . 4 2.2. Abbreviations . . . . . . . . . . . . . . . . . . . . . . 4 3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. Label Stack Entry Formats . . . . . . . . . . . . . . . . . . 5 4.1. LSE Format A: The MNA Sub-Stack Indicator . . . . . . . . 6 4.2. LSE Format B: The initial opcode . . . . . . . . . . . . 6 4.3. LSE Format C: Subsequent opcodes . . . . . . . . . . . . 7 4.4. LSE Format D: Additional Data . . . . . . . . . . . . . . 8 5. The MNA Sub-Stack . . . . . . . . . . . . . . . . . . . . . . 8 5.1. Opcodes . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.2. Data . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.3. Scope . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.4. Unknown Network Action Handling . . . . . . . . . . . . . 10 5.5. Ordering . . . . . . . . . . . . . . . . . . . . . . . . 11 6. Special Opcodes . . . . . . . . . . . . . . . . . . . . . . . 11 6.1. bSPL Protection . . . . . . . . . . . . . . . . . . . . . 11 6.2. Flag-Based NAIs without AD . . . . . . . . . . . . . . . 11 6.3. No-Operation Opcode . . . . . . . . . . . . . . . . . . . 12 6.4. Extension Opcode . . . . . . . . . . . . . . . . . . . . 12 7. NAS placement in the Label Stack . . . . . . . . . . . . . . 12 7.1. Actions when Pushing Labels . . . . . . . . . . . . . . . 13 8. Node Capability Signaling . . . . . . . . . . . . . . . . . . 14 9. Processing the Network Action Sub-Stack . . . . . . . . . . . 14 9.1. Encapsulating Node Responsibilities . . . . . . . . . . . 14 9.2. Transit Node Responsibilities . . . . . . . . . . . . . . 15 9.3. Penultimate Node Responsibilities . . . . . . . . . . . . 15 9.4. Egress Node Responsibilities . . . . . . . . . . . . . . 15 10. Network Action Indicator Opcode Definition . . . . . . . . . 15 11. Backward Compatibility . . . . . . . . . . . . . . . . . . . 16 12. Implementation Status . . . . . . . . . . . . . . . . . . . . 17 Rajamanickam, et al. Expires 8 June 2025 [Page 2] Internet-Draft MNA Sub-Stack Solution December 2024 12.1. University of Tuebingen Implementation . . . . . . . . . 17 13. Security Considerations . . . . . . . . . . . . . . . . . . . 17 14. Future IANA Considerations . . . . . . . . . . . . . . . . . 18 14.1. MPLS Network Actions Parameters . . . . . . . . . . . . 18 14.2. Network Action Flags Without Ancillary Data . . . . . . 18 14.3. Network Action Opcodes . . . . . . . . . . . . . . . . . 19 15. Examples . . . . . . . . . . . . . . . . . . . . . . . . . . 20 15.1. Network Action Encoding Examples . . . . . . . . . . . . 20 15.1.1. Network Action Flags without AD . . . . . . . . . . 20 15.1.2. Network Action Opcode with AD . . . . . . . . . . . 21 15.1.3. Network Action Opcode with more AD with Format-B . . 22 15.1.4. Network Action Opcode with more AD with Format C . . 23 15.2. Network Action Processing Order . . . . . . . . . . . . 23 15.2.1. Network Action Processing Order . . . . . . . . . . 24 16. References . . . . . . . . . . . . . . . . . . . . . . . . . 25 16.1. Normative References . . . . . . . . . . . . . . . . . . 25 16.2. Informative References . . . . . . . . . . . . . . . . . 26 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 26 Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 28 1. Introduction [RFC3032] defines the encoding of the MPLS label stack, the basic structure used to define a forwarding path. Forthcoming applications require MPLS packets to perform special network actions and carry optional Ancillary Data (AD) that can affect the packet forwarding decision or trigger Operations, Administration, and Maintenance (OAM) logging, for example. Ancillary Data can be used to carry additional information, such as a network slice identifier or an entropy value for load-balancing. Several MNA applications are described in [I-D.ietf-mpls-mna-usecases]. This solution document specifies In-stack network action and In-stack data (ISD) specific requirements found in [RFC9613]. This document defines the syntax and semantics of network actions and ancillary data encoded in an MPLS Label Stack. In-stack actions and ancillary data are contained in a Network Action Sub-Stack (NAS), which is recognized by the MNA Label. This document follows the framework specified in [I-D.ietf-mpls-mna-fwk]. This document describes an experiment whose purpose is to demonstrate that the MNA can be implemented and deployed. 2. Conventions Used in This Document Rajamanickam, et al. Expires 8 June 2025 [Page 3] Internet-Draft MNA Sub-Stack Solution December 2024 2.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 2.2. Abbreviations The terminology defined in [I-D.ietf-mpls-mna-fwk] and [RFC9613] is used in this document. +==============+=====================+==========================+ | Abbreviation | Meaning | Reference | +==============+=====================+==========================+ | AD | Ancillary Data | [RFC9613] | +--------------+---------------------+--------------------------+ | bSPL | Base Special | [RFC9017] | | | Purpose Label | | +--------------+---------------------+--------------------------+ | BOS | Bottom Of Stack | [RFC3032] | +--------------+---------------------+--------------------------+ | eSPL | Extended Special | [RFC9017] | | | Purpose Label | | +--------------+---------------------+--------------------------+ | HBH | Hop-By-Hop Scope | [I-D.ietf-mpls-mna-fwk] | +--------------+---------------------+--------------------------+ | I2E | Ingress-To-Egress | [I-D.ietf-mpls-mna-fwk] | | | Scope | | +--------------+---------------------+--------------------------+ | IHS | I2E, HBH, or Select | [I-D.ietf-mpls-mna-fwk], | | | Scope | This document | +--------------+---------------------+--------------------------+ | ISD | In-stack Data | [RFC9613] | +--------------+---------------------+--------------------------+ | LSE | Label Stack Entry | [RFC3032] | +--------------+---------------------+--------------------------+ | MNA | MPLS Network | [I-D.ietf-mpls-mna-fwk] | | | Actions | | +--------------+---------------------+--------------------------+ | NAI | Network Action | [RFC9613] | | | Indicator | | +--------------+---------------------+--------------------------+ | NAL | Network Action | This document | | | Length | | +--------------+---------------------+--------------------------+ | NAS | Network Action Sub- | [I-D.ietf-mpls-mna-fwk] | | | Stack | | Rajamanickam, et al. Expires 8 June 2025 [Page 4] Internet-Draft MNA Sub-Stack Solution December 2024 +--------------+---------------------+--------------------------+ | NASI | Network Action Sub- | This document | | | Stack Indicator | | +--------------+---------------------+--------------------------+ | NASL | Network Action Sub- | This document | | | Stack Length | | +--------------+---------------------+--------------------------+ | OAM | Operations, | [RFC6291] | | | Administration, and | | | | Maintenance | | +--------------+---------------------+--------------------------+ | RLD | Readable Label | [I-D.ietf-mpls-mna-fwk] | | | Depth | | +--------------+---------------------+--------------------------+ | TC | Traffic Class | [RFC5462] | +--------------+---------------------+--------------------------+ | TTL | Time To Live | [RFC3032] | +--------------+---------------------+--------------------------+ Table 1: Abbreviations 3. Overview The MPLS Network Action Sub-Stack (NAS) is a set of Label Stack Entries (LSEs) that appear as part of an MPLS Label Stack and serve to encode information about the network actions that should be invoked for the packet. Multiple NASes may appear in a label stack. This document describes how network actions and their optional ancillary data are encoded as part of an NAS as a stack of LSEs. Mechanisms that allow sharing of ancillary data AD between multiple network actions encoded in the same NAS can be described in other documents and do not rely on any explicit provision in the encodings described in this document. 4. Label Stack Entry Formats The NAS uses a variety of different formats of LSEs for different purposes. This section describes the syntax of the various formats while the overall structure of the NAS and the semantics of the various LSEs are described in the sections below. Rajamanickam, et al. Expires 8 June 2025 [Page 5] Internet-Draft MNA Sub-Stack Solution December 2024 4.1. LSE Format A: The MNA Sub-Stack Indicator LSE Format A is an LSE as described in [RFC3032] and [RFC5462]. The value for the MNA label is selected from the "240-255 experimental use" range in the "Extended Special-Purpose MPLS Label Values" registry. It indicates the presence of MNA in the packet and the start of an MNA sub-stack in the label stack. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label = 15 | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MNA-Label (TBA) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1: LSE Format A: The MNA Sub-Stack Indicator * S (1 bit) : The Bottom of Stack [RFC3032]. MUST be set to 0 on transmitted packets. If a packet is received with S bit set to 1, then the packet MUST be dropped. 4.2. LSE Format B: The initial opcode LSE Format B is used to encode the first opcode in the NAS, plus a number of other fields about the NAS. This LSE cannot carry more than 13 bits of data. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode | Data |R|IHS|S|U| NASL | NAL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2: LSE Format B: The initial opcode * Opcode (7 bits) : The operation code for this LSE. See Section 5.1. * Data (13 bits) : Opcode-specific data. * R (1 bit) : Reserved. This bit MUST be transmitted as zero and ignored upon receipt. * IHS (2 bits) : The scope of the sub-stack. See Section 5.3. Rajamanickam, et al. Expires 8 June 2025 [Page 6] Internet-Draft MNA Sub-Stack Solution December 2024 * S (1 bit) : The Bottom of Stack [RFC3032]. If NASL value is non- zero, then S bit MUST be 0. If a packet is received with S bit set to 1 and a non-zero NASL value, then the packet MUST be dropped. The encapsulating node MUST ensure that S bit is set to 1 only in the Last LSE. * U (1 bit): Unknown Network Action Handling. See Section 5.4. * NASL (4 bits) : The Network Action Sub-Stack Length (NASL). The number of additional LSEs in the sub-stack, not including the leading Format A LSE and the Format B LSE. * NAL (3 bits): Network Action Length. The number of LSEs of additional data, encoded in LSE Format D (Section 4.4) following this LSE. The NAL value MUST be less than or equal to the NASL value in Format B, if not the packet MUST be dropped. NOTE: Format A and B LSEs MUST be present when a Format C or D LSE is to be carried in the NAS. 4.3. LSE Format C: Subsequent opcodes LSE Format C is used to encode the subsequent opcodes in the NAS. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode | Data |S|U| Data | NAL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3: LSE Format C: Subsequent opcodes * Opcode (7 bits) : The operation code for this LSE. See Section 5.1. * Data (16 bits + 4 bits) : Opcode specific data * S (1 bit) : The Bottom of Stack [RFC3032]. If NAL value is non- zero and if S bit is set to 1, then the packet MUST be dropped. If this is not the last LSE in the NAS and if S bit is set to 1 then the packet MUST be dropped. The encapsulating node MUST ensure that S bit is set to 1 only in the Last LSE. * U (1 bit): Unknown Network Action Handling. See Section 5.4. Rajamanickam, et al. Expires 8 June 2025 [Page 7] Internet-Draft MNA Sub-Stack Solution December 2024 * NAL (3 bits): Network Action Length. The number of LSEs of additional data, encoded in LSE Format D (Section 4.4) following this LSE. The NAL value MUST be less than or equal to the NASL value in Format B, if not the packet MUST be dropped. 4.4. LSE Format D: Additional Data LSE Format D is used to encode additional data that did not fit in the LSE with the preceding opcode. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |1| Data |S| Data | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4: LSE Format D: Additional Data * 1 (1 bit) : The most significant bit MUST be set. This prevents legacy implementations from misinterpreting this LSE as containing a special purpose label if the data begins with zeros. * S (1 bit) : The Bottom of Stack [RFC3032]. If this is not the last LSE for the Network Action based on the NAL value and if S bit is set to 1 then the packet MUST be dropped. If this is not the last LSE in the NAS and if S bit is set to 1 then the packet MUST be dropped. The encapsulating node MUST ensure that the S bit is set to 1 only in the Last LSE. * Data (22 bits + 8 bits) : Opcode specific data 5. The MNA Sub-Stack The MNA Sub-Stack MUST begin with a Format A LSE (Section 4.1). The label field of the LSE contains the MNA Label (value TBA) to indicate the presence of the MNA Sub-Stack. The TC and TTL fields of the Format A LSE retain their semantics as defined in [RFC3032] and [RFC5462]. The TTL and TC fields in the Format A LSE are copied from the forwarding label at the top of the label stack. The penultimate node on the path may copy the TTL and TC fields from the preceding LSE to the next LSE on the label stack, overwriting the TTL and TC fields of the next LSE, as specified in Section 3.5 of [RFC3443]. If the node performing this copy is not aware of MNA, this could overwrite the values in the first LSE of the MNA sub-stack. Rajamanickam, et al. Expires 8 June 2025 [Page 8] Internet-Draft MNA Sub-Stack Solution December 2024 The second LSE in a NAS MUST be a Format B LSE (Section 4.2). This LSE contains an initial opcode plus additional fields that describe the NAS. The Format B LSE (Section 4.2) could optionally carry additional data in Format D (Section 4.4) LSEs, up to the length encoded in the LSE's NAL value. An NAS MAY contain more Format C (Section 4.3) and Format D (Section 4.4) LSEs, up to the length encoded in the NASL value. All Format D LSEs MUST follow a Format C or B LSE and be included in that LSE's NAL value. 5.1. Opcodes The opcode is a 7-bit field that indicates the semantics of its LSE. Several opcodes are assigned special semantics (Section 6), others act as Network Action Indicators (Section 10 and Section 14.3). 5.2. Data The data field carries opcode specific data. This is ancillary data for a network action. In the case of opcode 1, data field carries Flag-Based Network Action Indicators without ancillary data. To preserve backward compatibility, if a network action encodes data that will change during packet forwarding, then that data MUST be in the least significant 4 bits in the data field of a Format C LSE (Section 4.3) or the least significant 8 bits of a Format D LSE (Section 4.4). Some legacy implementations may use the label field in all LSEs when computing ECMP decisions and modifying the label field might disrupt that packet's flow. This is also applicable to opcode 1 Flag-Based Network Action Indicators those need to be changed in flight. 5.3. Scope The IHS field in the Format B LSE indicates the scope of the In-stack NAIs encoded in the NAS. Scope defines which nodes along the MPLS path should perform the network actions found within the NAS. The specific values of the IHS field are as follows: Rajamanickam, et al. Expires 8 June 2025 [Page 9] Internet-Draft MNA Sub-Stack Solution December 2024 +======+==========+ | Bits | Scope | +======+==========+ | 00 | I2E | +------+----------+ | 01 | HBH | +------+----------+ | 10 | Select | +------+----------+ | 11 | Reserved | +------+----------+ Table 2: IHS Scope Values Ingress To Egress (I2E) - The NAS MUST NOT be processed by any node the except the egress node. Hop-By-Hop (HBH) - All nodes along the path MUST process the NAS. Select - Only specific nodes along the path that brings NAS to top of the stack will perform the action. A single NAS carries only one of the three scopes (I2E/HBH/Select). To support multiple scopes for a single packet, multiple NASes MAY be included in a single label stack. The egress node is included in the HBH scope. This implies that the penultimate node MUST NOT remove a HBH NAS. The egress node MAY receive a NAS at the top of the label stack as discussed in Section 10. An I2E scope NAS, if present, MUST be encoded after any HBH or Select-scope NASes. This makes it easier for the transit nodes to process a NAS with HBH or Select scope. 5.4. Unknown Network Action Handling The Unknown Network Action Handling (U) field in a Format B LSE (Section 4.2) and Format C LSE (Section 4.3) is a 1-bit value that defines the action to be taken by a node that does not understand an action within the NAS. The different types of Unknown Network Action Handling actions are defined below. Rajamanickam, et al. Expires 8 June 2025 [Page 10] Internet-Draft MNA Sub-Stack Solution December 2024 +=====+=====================+ | Bit | Action | +=====+=====================+ | 0 | Skip to the next NA | +-----+---------------------+ | 1 | Drop the packet | +-----+---------------------+ Table 3: Unknown Network Action Handling When a packet with an unknown Network Action is dropped, the node SHOULD maintain a local counter for this event, and MAY send a rate- limited notification to the operator. 5.5. Ordering The network actions encoded in the NAS MUST be processed as if they were processed in the order that they appear in the NAS, from the top of the NAS to the bottom. NAI encoded as flags (see Section 6.2) MUST be processed as if they were processed from the most significant bit to the least significant bit. If a label stack contains multiple NASes, then they MUST be processed as if they were processed in the order that they appear in the label stack, subject to the restrictions in Section 7. 6. Special Opcodes Below are the special opcodes used to build a basic In-stack MNA solution. In future, additional special opcodes can be defined and their code-points can be assigned from the "Network Action Opcodes" registry. 6.1. bSPL Protection Opcode: 0 Purpose: Legacy implementations may scan the label stack looking for bSPL values. As long as the opcode field is non-zero, an LSE cannot be misinterpreted as containing a bSPL. Opcode 0 is therefore reserved and is not used. 6.2. Flag-Based NAIs without AD Opcode: 1 Rajamanickam, et al. Expires 8 June 2025 [Page 11] Internet-Draft MNA Sub-Stack Solution December 2024 Purpose: Network actions that do not require Ancillary Data do not require an entire LSE. A single flag can be used to indicate each of these network actions. LSE Formats: B, C, D Data: The data field carries Network Action Indicators, which should be evaluated from the most significant bit to the least significant bit. If this opcode is used with LSE Format B only, then up to 13 flags may be carried. If this opcode is used with LSE Format C only, then up to 20 flags may be carried. Format D LSEs can be used with format C LSEs to encode more than 20 flags. Flags are assigned from the "Network Action Flags Without Ancillary Data" registry (Section 14.2). If flags need to be evaluated in a different order, multiple LSEs using this opcode may be used to specify the requested order. Scope: This opcode can be used with any scope. 6.3. No-Operation Opcode Opcode: 2 Purpose: This opcode is reserved to indicate that this opcode does not perform any Network Action and MUST be skipped. Scope: Format B. 6.4. Extension Opcode Opcode: 127 Purpose: This opcode is reserved to extend the current opcode range beyond 127 in future. If this opcode is not supported, then the packet with the opcode 127 MUST be dropped. Use of this opcode is outside the scope of this document. 7. NAS placement in the Label Stack The node adding an NAS to the label stack places a copy of the NAS where the relevant nodes can read it. Each downstream node along the path has a Readable Label Depth (RLD) [I-D.ietf-mpls-mna-fwk]. If the NAS is to be processed by a downstream MNA-capable node, then the entire NAS MUST be placed so that it is within RLD by the time the packet reaches the downstream MNA-capable node and the NAS MUST NOT appear at the top of the stack at any MNA incapable node on the path. Rajamanickam, et al. Expires 8 June 2025 [Page 12] Internet-Draft MNA Sub-Stack Solution December 2024 If the label stack is deep, several copies of the NAS may need to be encoded in the label stack. For a NAS with HBH scope, every node will process the top copy of the NAS. For a NAS with Select scope, it is processed by the node that brings it to the top of stack and then the NAS is removed from the stack. The select-scoped NAS needs to be inserted after the forwarding label and needs to be inserted before the next forwarding label. It could be inserted before or after a HBH NAS. For I2E scope, only one copy of the NAS needs to be added at the bottom of the stack. Transit, non-penultimate nodes that pop a forwarding label and expose a copy of a NAS MUST remove it. A node performing Penultimate Hop Popping (PHP) that pops the forwarding label with only the NAS(es) remaining on the stack MUST NOT remove the NAS(es). Instead, it forwards the packet with the NAS(es) at the top of stack to the next node. The node that receives the NAS at the top of the label stack MUST remove it. 7.1. Actions when Pushing Labels An MNA-capable node may need to push additional labels as well as push new network actions onto a received packet. While pushing additional labels on to the label stack of the receive packet, the MNA-capable node MUST verify that the entire top-most NAS with HBH scope is still within the RLD of the downstream MNA-capable nodes. If required, the MNA-capable node MAY create a copy of the top-most NAS with HBH scope and insert it within the RLD of the downstream MNA-capable nodes on the label stack. When an MNA-capable node needs to push a new NAS with HBH scope on to a received packet that already has an NAS with HBH scope, it SHOULD copy (and merge) the network actions (including their Ancillary Data) from the received top-most NAS with HBH scope in the new NAS with HBH scope. The new NAS MUST be placed within the RLD of the downstream MNA-capable nodes. This behavior can be based on local policy. The new network actions added MUST NOT conflict with the network actions in the received NAS with HBH scope. The mechanism to resolve such conflicts depend on the network actions and can be based on Rajamanickam, et al. Expires 8 June 2025 [Page 13] Internet-Draft MNA Sub-Stack Solution December 2024 local policy. The MNA-capable node that pushes entries MUST understand any network actions which it is pushing which may result in a conflict, and MUST resolve any conflicts between new and received network actions. In the usual case of a conflict of duplicating a network action, the definition of the network action will generally give guidance on likely resolutions. 8. Node Capability Signaling Encapsulating Node is the node that pushes an NAS on to the Label stack. The encapsulating node MUST make sure that the NAS can be processed by the transit and egress nodes. * The path computation system needs to know the MSD and RLD that can be imposed at the ingress node of a given SR path [RFC8664]. This ensures that the label stack depth of a computed path does not exceed the maximum number of labels (i.e., MSD) the node is capable of imposing and the maximum number of labels that can be read by the MNA-processing nodes in the path. The MSD needs to include the MNA Sub-Stacks to be added. * The node responsible for selecting a path through the MPLS network needs to know and consider the MNA-capabilities and RLD of the transit nodes, and the MNA-capabilities of the end point. it supports. * Information about the capabilities of the nodes may be configured, collected through management protocols, or distributed by control protocols (such as advertising by routing protocols). * The mechanisms by which the capabilities of the nodes are known by the node responsible for selecting a path through the MPLS network are out of scope for this document. 9. Processing the Network Action Sub-Stack This section defines the specific responsibilities for nodes along an LSP. 9.1. Encapsulating Node Responsibilities The encapsulating node MAY add NASes to the label stack in accordance with its policies, the placement restrictions in Section 7, and the limitations learned from Section 8. Rajamanickam, et al. Expires 8 June 2025 [Page 14] Internet-Draft MNA Sub-Stack Solution December 2024 The encapsulating node MUST NOT add an NAS to the label stack if the egress node does not support MNA. If there is an existing label stack, the encapsulating node MUST NOT modify the first 20 bits of any LSE in the label stack when the ECMP technique in the network is using the hashing of the labels on the label stack. If the encapsulating node is also a transit node, then it MUST also follow the rules set out in Section 9.2. 9.2. Transit Node Responsibilities Transit Node is the node that process an NAS on to the Label stack but does not push any new NAS. The transit node MUST NOT modify the first 20 bits of any LSE in the label stack when the ECMP technique in the network is using the hashing of the labels on the label stack. A transit node MAY change the Ancillary Data found in the least significant 8 bits of an LSE. Transit nodes MUST process the NASes in the label stack, according to the rules set out in Section 5.5. A transit node that processes an NAS and does not recognise the value of an opcode MUST follow the rules according to the setting of the Unknown Action Handling value in the NAS as described in (Section 5.4). 9.3. Penultimate Node Responsibilities In addition to the transit node responsibilities, the penultimate node and penultimate SR-MPLS segment node MUST NOT remove the last copy of an HBH or I2E NAS when it is exposed after removing the forwarding (transport) label. This allows the egress node to process the NAS. 9.4. Egress Node Responsibilities The egress node MUST remove any NAS it receives. 10. Network Action Indicator Opcode Definition The following information MUST be defined for new Network Action Indicator opcode request in the document that specifies the Network Action. Rajamanickam, et al. Expires 8 June 2025 [Page 15] Internet-Draft MNA Sub-Stack Solution December 2024 A request for a new NAI MUST include the following information: * Format: The definition of the new Network Action MUST specify the LSE Formats. The opcode can define Network Action in Format B or C or both B and C. Both Format B and C LSEs MAY optionally carry Format D LSE(s). * Scope: The request MUST specify at-least one scope (I2E, HBH, Select) for the Network Action. The request MAY specify more than one scope. * Ancillary Data: A request MUST specify the quantity, syntax, and semantics of any associated Ancillary Data. The Ancillary Data MAY be variable length, but the length MUST be computable based on the data present in the NAS. * Processing: The request MUST specify the detailed procedure for processing the network action. * Interactions: The definition of the new Network Action MUST specify its interaction with other currently defined Network Action if there is any. An assignment for an NAI MAY make requests from any combination of the "Network Action Opcodes" or "Network Action Flags Without Ancillary Data" assignments. This decision should optimize for eventual encoding efficiency. If the NAI does not require any ancillary data, then a flag is preferred as only one bit is used in the encoding. 11. Backward Compatibility This section discusses interactions between MNA-capable and legacy, non-MNA-capable nodes. An MNA-encapsulating node MUST ensure that the MPLS Network Action Sub-Stack indicator is not at the top of the MPLS Label Stack when the packet arrives at a non-MNA-capable node. If such a packet did arrive at a non-MNA-capable node, it will most likely be dropped. Legacy nodes may scan the label stack, potentially looking for a label field containing a bSPL. To ensure that the LSE formats described herein do not appear to contain a bSPL value, the opcode value of 0 has been reserved. By ensuring that there is a non-zero value in the high order 7 bits, we are assured that the high order 20 bits cannot be misinterpreted as containing a bSPL value (0-15). Rajamanickam, et al. Expires 8 June 2025 [Page 16] Internet-Draft MNA Sub-Stack Solution December 2024 The TC and TTL fields of the Format A LSE are not re-purposed for encoding, as the penultimate node on the MPLS packet path may propagate TTL from the transport (or forwarding) label to the next label on the label stack, overwriting the TTL on the next label. If the penultimate node is a legacy node, it might perform this action, potentially corrupting other values stored in the TC and TTL fields. To protect against this, we retain the TC and TTL fields in the Format A LSE. 12. Implementation Status [Note to the RFC Editor - remove this section before publication, as well as remove the reference to [RFC7942]] This section records the status of known implementations of the protocol defined by this specification at the time of posting of this Internet-Draft, and is based on a proposal described in [RFC7942]. The description of implementations in this section is intended to assist the IETF in its decision processes in progressing drafts to RFCs. Please note that the listing of any individual implementation here does not imply endorsement by the IETF. Furthermore, no effort has been spent to verify the information presented here that was supplied by IETF contributors. This is not intended as, and must not be construed to be, a catalog of available implementations or their features. Readers are advised to note that other implementations may exist. 12.1. University of Tuebingen Implementation The solution defined in the document draft-ietf-mpls-mna-hdr-08 has been implemented using P4 pipeline. The implementation code can be found at https://github.com/uni-tue-kn/P4-MNA. 13. Security Considerations The security considerations in [RFC3032] also apply to this document. In addition, MNA-creates a new dimension in security concerns: * The actions of an encapsulating node can affect any or all of the nodes along the path. In the most common and benign situations, such as a syntactically incorrect packet could result in packet loss or corruption. Rajamanickam, et al. Expires 8 June 2025 [Page 17] Internet-Draft MNA Sub-Stack Solution December 2024 * The semantics of a network action are unbounded and may be insecure. A network action could be defined that made arbitrary changes to the memory of the forwarding router, which could then be used by the encapsulating node to compromise every MNA-capable router in the network. The IETF needs to ensure that only secure network actions are defined. * The MNA architecture supports locally-defined network actions. For such actions, there will be limited oversight to ensure that the semantics do not create security issues. Implementors and network operators will need to ensure that locally-defined network actions do not compromise the security of the network. * The MNA architecture supports modifying the AD on the intermediate nodes, so the critical network functions should either not rely on the data or should be aware of the risks and use other means to verify the security of the whole network. * The "private Use" opcodes in "Network Action Opcodes" Section 14.3 and "Network Action Flags Without Ancillary Data" Section 14.2 Registry are subject to the considerations described in [RFC8126]. 14. Future IANA Considerations 14.1. MPLS Network Actions Parameters This document requests to create a new category called "MPLS Network Actions Parameters" within the "Multiprotocol Label Switching Architecture (MPLS)" category. The registries described below should belong to this new category. 14.2. Network Action Flags Without Ancillary Data This document requests to create a new registry with the name "Network Action Flags Without Ancillary Data". Registration requests should comply with Section 10. The registration procedure for this registry is "IETF Review", "Experimental Use" and "Private Use" as defined in [RFC8126]. The fields in this registry are "Bit Position" (integer), "Description" (string), and "Reference" (string). Rajamanickam, et al. Expires 8 June 2025 [Page 18] Internet-Draft MNA Sub-Stack Solution December 2024 Bit Position refers to the position relative to the most significant bit in LSE Format B or C Data fields and any subsequent Format D LSEs. Bit Position 0 is the most significant bit in an LSE Format B or C Data field. Bit Position 20 is the most significant bit in the first LSE Format D Data field. There are 20 bits available in LSE Format C and 30 bits available in LSE Format D. There are at most 14 Format D LSEs per opcode (due to NASL limit of 15 and Format D requires Format C LSE), so there are at most 20 + 14 * 30 = 440 bit positions. The Bit Position is an integer with value 0-469. The initial assignments for this registry are: +==============+==================+===============+ | Bit Position | Description | Reference | +==============+==================+===============+ | 0-14 | IETF Review | This document | +--------------+------------------+---------------+ | 15-16 | Experimental Use | This document | +--------------+------------------+---------------+ | 17-19 | Private Use | This document | +--------------+------------------+---------------+ | 20-469 | IETF Review | This document | +--------------+------------------+---------------+ Table 4: Network Action Flags Without Ancillary Data Registry 14.3. Network Action Opcodes This document requests to create a new registry with the name "Network Action Opcodes". Registration requests should comply with Section 10. The registration procedure for this registry is "IETF Review", "Experimental Use" and "Private Use" as defined in [RFC8126]. The fields are "Opcode" (integer), "Description" (string), and "Reference" (string). Opcode is an integer with value 1-126. +=========+==================+===============+ | Opcode | Description | Reference | +=========+==================+===============+ | 1-110 | IETF Review | This document | +---------+------------------+---------------+ | 111-114 | Experimental Use | This document | +---------+------------------+---------------+ | 115-126 | Private Use | This document | +---------+------------------+---------------+ Table 5: Network Action Opcodes Rajamanickam, et al. Expires 8 June 2025 [Page 19] Internet-Draft MNA Sub-Stack Solution December 2024 This document has allocated values for the following Network Action Opcodes from "Network Action Opcodes". +========+===========================+===============+ | Opcode | Description | Reference | +========+===========================+===============+ | 0 | Reserved | This document | +--------+---------------------------+---------------+ | 1 | Flag-Based Network Action | This document | | | Indicators without AD | | +--------+---------------------------+---------------+ | 2 | No operation Opcode | This document | +--------+---------------------------+---------------+ | 127 | Opcode Range Extension | This document | | | Beyond 127 | | +--------+---------------------------+---------------+ Table 6: Network Action Opcodes 15. Examples 15.1. Network Action Encoding Examples 15.1.1. Network Action Flags without AD 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label = 15 | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MNA-Label (TBA) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=1 | Flags |R|IHS|S|U|NASL=0 |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5: NAS with Network Action Flags This is an example of an NAS with Flag-Based NAIs without Ancillary Data. Details: Opcode=1: This opcode to indicates that the LSE carries Flag-Based NAIs without AD. Data: The data field carries the Flag-Based NAIs. Rajamanickam, et al. Expires 8 June 2025 [Page 20] Internet-Draft MNA Sub-Stack Solution December 2024 S: This is the bottom of stack bit. Set if and only if this LSE is the bottom of the stack. U: Action to be taken if one of the NAIs are not recognized by the processing node. NASL: The NASL value is set to 0, as there are no additional LSEs. NAL: The NAL value is set to 0, as there are no additional AD encoded using Format D. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label = 15 | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MNA-Label (TBA) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=2 | Data=0 |R|IHS|S|U|NASL=2 |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=1 | Flag-Based NAIs |S|U| NAIs |NAL=1| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |1| Additional Flag-Based NAIs |S|Flag-Based-NAIs| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 6: Network Action Flags without AD using LSE Format D In this example, the NAS contains a Format B LSE with No-Operation Opcode value 2. The next LSE uses Format C, but the Network Action Flag is not in a bit position contained within the Format C LSE, so a single Format D LSE has been added to the NAS to carry the flag. NAL is set to 1 to indicate that Flag-Based NAIs are also encoded in the next LSE. NASL is set to 2 to indicate that 2 additional LSEs are used. 15.1.2. Network Action Opcode with AD 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label = 15 | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MNA-Label (TBA) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=8 | Ancillary Data |R|IHS|S|U|NASL=0 |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Rajamanickam, et al. Expires 8 June 2025 [Page 21] Internet-Draft MNA Sub-Stack Solution December 2024 Figure 7: Network action opcode with Ancillary Data In this example, the NAS is carrying only one Network Action that requires 13 bits of Ancillary Data. Details on the Second LSE Opcode=8: A network action allocation is outside of this document. Data: The data field contains 13 bits of ancillary data. 15.1.3. Network Action Opcode with more AD with Format-B A network action may require more Ancillary Data than can fit in a single LSE. In this example, a Format D LSE is added to carry additional Ancillary Data. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label = 15 | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MNA-Label (TBA) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=10 | Ancillary Data |R|IHS|S|U|NASL=1 |NAL=1| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |1| Ancillary Data |S|Ancillary Data | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 8: Network Action With Additional Ancillary Data In this example, opcode 10 is encoded in Format B and it requires more than one LSE's worth of Ancillary Data, so a Format D LSE is added. Details on the second LSE: Opcode=10: An opcode allocation is outside of this document Ancillary Data: Ancillary data required to process the Network Action opcode 10 NAL: Length of additional LSEs used to encode its Ancillary data Details on the third LSE: Ancillary Data: 22 bits of additional Ancillary data. Rajamanickam, et al. Expires 8 June 2025 [Page 22] Internet-Draft MNA Sub-Stack Solution December 2024 Ancillary Data: 8 bits of additional Ancillary Data. 15.1.4. Network Action Opcode with more AD with Format C A network action may require more Ancillary Data than can fit in a single LSE. In this example, a Format D LSE is added to carry additional Ancillary Data. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label = 15 | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MNA-Label (TBA) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=2 | Data=0 |R|IHS|S|U|NASL=2 |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=9 | Ancillary Data |S|U| AD |NAL=1| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |1| Ancillary Data |S|Ancillary Data | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 9: Network Action With Additional Ancillary Data In this example, opcode 9 requires more than one LSE's worth of Ancillary Data, so a Format D LSE is added. Details on the third LSE: Opcode=9: An opcode allocation is outside of this document Ancillary Data: Most significant bits of Ancillary data AD: 4 bits of additional Ancillary Data Details on the fourth LSE: Ancillary Data: 22 bits of additional Ancillary data. Ancillary Data: 8 bits of additional Ancillary Data. 15.2. Network Action Processing Order The semantics of a network action can vary widely and the results of processing one network action may affect the processing of a subsequent network action. See Section 5.5. Rajamanickam, et al. Expires 8 June 2025 [Page 23] Internet-Draft MNA Sub-Stack Solution December 2024 15.2.1. Network Action Processing Order 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label = 15 | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MNA-Label (TBA) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=8 | Ancillary Data |R|IHS|S|U|NASL=2 |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=7 | Ancillary Data7 |S|U| AD7 |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=1 | Flag-Based NAIs |S|U| NAI |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 10: In-stack NA processing order In this example, opcode 8 is processed first, then opcode 7, and then the network action flags are processed from most significant to least significant. In a different case, some Flag-Based NAIs may need to be processed before opcode 7 and some Flag-Based NAIs may need to be processed after Opcode 7. This can be done by causing some NAIs to appear earlier in the NAS. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label = 15 | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MNA-Label (TBA) | TC |S| TTL | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=8 | Ancillary Data |R|IHS|S|U|NASL=3 |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=1 | 0x01 |S|U| NAI |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=7 | Ancillary Data7 |S|U| AD7 |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Opcode=1 | 0x02 |S|U| NAI |NAL=0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 11: Interleaving network actions Rajamanickam, et al. Expires 8 June 2025 [Page 24] Internet-Draft MNA Sub-Stack Solution December 2024 In the above example, opcode 8 is processed first, then Flag-Based NAI 0x01 is processed, then opcode 7 is processed, and finally NAI 0x02 is processed. 16. References 16.1. Normative References [I-D.ietf-mpls-mna-fwk] Andersson, L., Bryant, S., Bocci, M., and T. Li, "MPLS Network Actions (MNA) Framework", Work in Progress, Internet-Draft, draft-ietf-mpls-mna-fwk-14, 2 December 2024, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack Encoding", RFC 3032, DOI 10.17487/RFC3032, January 2001, . [RFC3443] Agarwal, P. and B. Akyol, "Time To Live (TTL) Processing in Multi-Protocol Label Switching (MPLS) Networks", RFC 3443, DOI 10.17487/RFC3443, January 2003, . [RFC5462] Andersson, L. and R. Asati, "Multiprotocol Label Switching (MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic Class" Field", RFC 5462, DOI 10.17487/RFC5462, February 2009, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC9017] Andersson, L., Kompella, K., and A. Farrel, "Special- Purpose Label Terminology", RFC 9017, DOI 10.17487/RFC9017, April 2021, . [RFC9613] Bocci, M., Ed., Bryant, S., and J. Drake, "Requirements for Solutions that Support MPLS Network Actions (MNAs)", RFC 9613, DOI 10.17487/RFC9613, August 2024, . Rajamanickam, et al. Expires 8 June 2025 [Page 25] Internet-Draft MNA Sub-Stack Solution December 2024 16.2. Informative References [I-D.ietf-mpls-mna-usecases] Saad, T., Makhijani, K., Song, H., and G. Mirsky, "Use Cases for MPLS Network Action Indicators and MPLS Ancillary Data", Work in Progress, Internet-Draft, draft- ietf-mpls-mna-usecases-15, 23 September 2024, . [RFC6291] Andersson, L., van Helvoort, H., Bonica, R., Romascanu, D., and S. Mansfield, "Guidelines for the Use of the "OAM" Acronym in the IETF", BCP 161, RFC 6291, DOI 10.17487/RFC6291, June 2011, . [RFC7942] Sheffer, Y. and A. Farrel, "Improving Awareness of Running Code: The Implementation Status Section", BCP 205, RFC 7942, DOI 10.17487/RFC7942, July 2016, . [RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, June 2017, . [RFC8664] Sivabalan, S., Filsfils, C., Tantsura, J., Henderickx, W., and J. Hardwick, "Path Computation Element Communication Protocol (PCEP) Extensions for Segment Routing", RFC 8664, DOI 10.17487/RFC8664, December 2019, . Acknowledgments The authors of this document would like to thank the MPLS Working Group Open Design Team for the discussions and comments on this document. The authors would also like to thank Amanda Baber for reviewing the IANA Considerations and providing many useful suggestions. The authors would like to thank Loa Andersson, Stewart Bryant, Greg Mirsky, Joel M. Halpern and Adrian Farrel for reviewing this document and providing many useful suggestions. The authors would like to thank Fabian Ihle and Michael Menth, both from University of Tuebingen, for implementing the solution defined in this document in P4 pipeline. Rajamanickam, et al. Expires 8 June 2025 [Page 26] Internet-Draft MNA Sub-Stack Solution December 2024 Contributors The following people have substantially contributed to this document: Jisu Bhattacharya Cisco Systems, Inc. Email: jisu@cisco.com Bruno Decraene Orange Email: bruno.decraene@orange.com Weiqiang Cheng China Mobile Email: chengweiqiang@chinamobile.com Xiao Min ZTE Corp. Email: xiao.min2@zte.com.cn Luay Jalil Verizon Email: luay.jalil@verizon.com Jie Dong Huawei Technologies Huawei Campus, No. 156 Beiqing Rd. Beijing 100095 China Email: jie.dong@huawei.com Tianran Zhou Huawei Technologies China Email: zhoutianran@huawei.com Bin Wen Comcast Email: Bin_Wen@cable.comcast.com Rajamanickam, et al. Expires 8 June 2025 [Page 27] Internet-Draft MNA Sub-Stack Solution December 2024 Sami Boutros Ciena Email: sboutros@ciena.com Tony Li Juniper Networks United States Email: tony.li@tony.li John Drake Juniper Networks United States Email: jdrake@juniper.net Figure 12 Authors' Addresses Jaganbabu Rajamanickam (editor) Cisco Systems, Inc. Canada Email: jrajaman@cisco.com Rakesh Gandhi (editor) Cisco Systems, Inc. Canada Email: rgandhi@cisco.com Royi Zigler Broadcom Email: royi.zigler@broadcom.com Haoyu Song Futurewei Technologies Email: haoyu.song@futurewei.com Kireeti Kompella Juniper Networks United States Email: kireeti.ietf@gmail.com Rajamanickam, et al. Expires 8 June 2025 [Page 28]